NTI st-ipfo4k18gb-lc 4K 18Gbps HDMI Extender Over IP

NTI, st-ipfo4k18gb-lc, 4K 18Gbps HDMI Extender Over IP via One LC Fiber Optic Cable, Transmitter and Receiver Set

st-ipfo4k18gb-lc Includes Only:

• One transmitter unit
• One receiver unit
• One T1270/R1330nm 10G Base-T SFP module
• One T1330/R1270nm 10G Base-T SFP module
• One IR emitter
• One IR receiver
• Two power supplies
• Mounting brackets

Features:

• Signal transmission via single-strand LC fiber optic cable.
  • Using singlemode 9-micron cable, extend to 24.8 miles (40 km).
  • Using 50-micron OM2 (or better) multimode cable, extend to 1,640 feet (500 meters).
  • Zero latency.
• Supports Ultra-HD 4Kx2K resolutions to 3840x2160 and 4096x2160 at60Hz YUV 4:4:4, HDTV resolutions to 1080p at60Hz, and up to 1920x1200 (WUXGA).
• Cascade network switches to extend the length longer distances.
  • Up to 12 switches can be cascaded.
• HDMI features supported:
  • HDMI 2.0
  • 8-bit, 10-bit, and 12-bit Deep Color
  • Dolby TrueHD, DTS-HD Master Audio, Dolby Digital, Dolby Digital+, Dolby Atmos, LPCM 7.1CH, DTS 5.1, and DTS:X
  • RGB, YCbCr 4:4:4, YCbCr 4:2:2, and YCbCr 4:2:0/li>
  • Bandwidth up to 600 Mhz (18Gbps)
  • 3D (1080p at60Hz)
  • Support for CEC (consumer electronic control) compatible devices.
  • HDR10
  • ARC
• HDCP 2.2 and 1.4 compliant.
• Supports local and remote HDMI displays.
• For a point-to-many connection, a standalone network with an unmanaged 10G SFP network switch, hub, or router can be used instead of a managed SFP network switch.
  • Easily expandable. Add remote units as you add monitors.
    • Up to 255 receivers supported.
  • It is not recommended to use any other network devices on this standalone network as it may cause degradation in performance.
• Support for multiple transmitters (many-to-many connection) requires a managed 10G SFP network switch with IGMP support and Jumbo frame support. Standard LAN switches can only support one transmitter.
  • The managed 10G SFP network switch must support port-based IEEE 802.1Q VLAN.
  • Each VLAN acts as a separate HDMI Over IP Channel on the network.
    • Each VLAN channel supports one transmitter.
  • The number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
• Plug and play installation allows receivers to find the transmitters automatically on the same subnet.
• Local and remote units must be in the same LAN. The units do not support WAN connections.
• Built-in default EDID table.
• Supports full-duplex RS232 up to 115200 baud.
• Bi-directional IR control from input and output locations.
• Supports HDMI embedded digital audio and ARC audio extraction via Toslink connection.
• Built-in surge and ESD protection.
• Mounting brackets included for easy surface/wall mounting.

The XTENDEX® 4K 18Gbps HDMI Extender Over IP via Fiber Optic Cable locates an Ultra-HD 4Kx2K 60Hz 4:4:4 HDMI display, audio, IR, and RS232 up to 24.8 miles (40 kilometers) away from an HDMI source using a single LC singlemode fiber optic strand or 1,640 feet (500 meters) using LC multimode fiber optic cable.

Each 4K 18Gbps HDMI Extender Over IP consists of a local unit that connects to an HDMI source and a local display via the HDMI loop output, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via Fiber Optic Cable or a Point-to-Many connection via a 10G SFP network switch. Support for multiple transmitters requires a managed 10G SFP network switch.